Lumateq LT848-20-110-00 Bedienungsanleitung PDF herunterladen (Seite 2)

LUMATEQ is a division of TACO Metals, Inc.

To view the entire portfolio of LUMATEQ products and for Warranty and Product Information, go to lumateq.com

INSTRUCTIONS

INSTRUC-LT848-20-110-00

Tube Lamp (LT848-20-110-00)

Caution:

• Thisproductistobeinstalledinadrylocationonlybyaqualiedelectricianaccordingtothe

NationalElectricalCodeandallapplicablelocalcodesandregulations.

• Donotinstallindimmingcircuitsoremergencyxtures.

• Donotopenthislamp.Nouserserviceablepartsinside.

• Theseretrotlampsareonlypoweredfromtheoneendmarked“Connect this end to live (powered) end”.

Installation Instructions:

Youwillneedafewfeetof600V18GaugeSolidTFF,TFNorAWMwireforthisinstallation.Onlythistypeofsolidwirewill

workwiththepush-inwiretrapsinthelampholder.Thisretrotconversionlampwillnotworkwithshuntedsockets,typically

usedwith“INSTANTSTART”ballasts.Determineifthexturehasshuntedornon-shuntedlampholders.Ifthextureusesa

shuntedlampholder,replaceitwiththenon-shuntedlampholderfurnishedwiththislamp.However,notallshuntedsockets

haveonesetofpush-inwiretrapsblankedoff.Ifnotsure,checkforcontinuitybetweenthetwosetsofholes.Ifthereis

continuity,thesocketisshuntedandneedstobereplacedbytheincludednon-shuntedsocket.Therearemanydifferent

non-shuntedsockets.Somearetall,someareshort.Someslideinandsomesnapin.Someslideandsnapin.Othersare

screw-downsurfacemountsockets.Itdependsontheageandtypeofxture.Whiletheincludednon-shuntedlampholder

willtmostxtures,itmaynottyours.Ifitdoesn’t,consultyourlocalelectricaldistributor.

1) Turnoffthepowertothelightxtureatthecircuitbreakerpanelorfusebeforeinstallation.

2) DisconnecttheblackandwhiteballastINPUTleadsfromthe100-277VACsupplywires.Disconnecttheballastfrom

alllampsocketsbycuttingthewires.Ifastarterispresentandprotrudingfromthexture,cutthewirestothestarter

base,butleavethestarterinplace,soasnottocreateapotentiallyunsafeopeninginthexture.

3) Removetheballast.

4) Cuttwolengthsof600V18GaugeSolidTFF,TFNorAWMwirelongenoughtoreachfromthelampholdertothe

100-277VACsupplywires.

5) Strip3/8”ofinsulationfrombothendsofbothleads.

6) Insertonestrippedendofeachsolidwireintoeachsideofthelampholder.

7) Connectthesetwowirestothe100-277VACsupplywiresusingULlistedtwist-onwireconnectors(wirenuts).

8) Allremainingseveredwiresthatarenolongerusedneedtoberemovedcompletelyororganizedandcappedoff

usingULlistedwirenutssotheydon’tinterferewiththereassemblyofthexture.

9) Inserttheendoftheretrotlampthatismarked“Connect this end to live (powered) end”intothenon-shunted

lampholderconnectedtothesupplywires.

10) Checkthenewconnectionsforstructuralintegrity.Thismeansthewiresshouldnotcomeapartwhenpulledcasually.

11) AfxincludedadhesiveCAUTIONlabeltothexturewhereitwillbeseenwhenthisretrotlampisremovedfor

replacement.Thislabelwarnstonotreplacethisretrotlampwithastandarduorescentlamporanydifferenttype

ofretrotlampotherthantheTOPAZlampslistedunderthetitleofthisdocument.

12) Restorepoweratthecircuitbreakerorfuse.

13) Turnonxture.

WARNING

1 2

INSTRUCTIONS 1

Kommentare zu diesen Handbüchern

Keine Kommentare

Lumateq LT848-20-110-00 Bedienungsanleitung Seite 2

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Beleuchtung Lumateq LT848-20-110-00